Vivotek SD9363-EHL User Manual Download

Page: 162 / 332

VIVOTEK

User's Manual - 162

7.6.7.1 RTSP multicast

Subgroup of

network_rtsp_s<0~(n-1)>

multicast

n is stream count

NAME

VALUE

SECURITY
(get/set)

DESCRIPTION

alwaysmulticast

4/4

Enable always multicast.

ipaddress

4/4

Multicast IP address.

videoport

1025 ~ 65535

4/4

Multicast video port.

audioport

1025 ~ 65535

4/4

Multicast audio port.
(capability.naudioin > 0)

metadataport

1026~65534

4/4

Multicast metadata port.

ttl

1 ~ 255

4/4

Multicasttime to live value.

7.6.8 SIP port

Subgroup of

network

sip

(capability.protocol.sip> 0)

NAME

VALUE

SECURITY
(get/set)

DESCRIPTION

port

1025 ~ 65535

1/6

SIP port.

7.6.9 RTP port

Subgroup of

network

rtp

NAME

VALUE

SECURITY
(get/set)

DESCRIPTION

videoport

1025 ~ 65535

6/6

Video channel port for RTP.
(capability.protocol.rtp_unicast=1)

audioport

1025 ~ 65535

6/6

Audio channel port for RTP.
(capability.protocol.rtp_unicast=1)

metadataport

1025 ~ 65535

6/6

Metadata channel port for RTP.

7.6.10 PPPoE

Subgroup of

network

pppoe

(capability.protocol.pppoe > 0)

NAME

VALUE

SECURITY
(get/set)

DESCRIPTION

user

string[128]

6/6

PPPoE account user name.

Summary of Contents for SD9363-EHL













































































































































































































































































































































Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands

Vivotek SD9363-EHL, User Manual

Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands