Vivotek SD9363-EHL User Manual Download

Page: 8 / 332

VIVOTEK

8 - User's Manual

Status LED

Item LED status

Description

Steady

red

Power on and system booting

Red

LED OFF

Power off

Steady

red

Green

blinking every 1 sec.

Network normal (heartbeat)

Steady

red

Green

LED OFF

Network failed

Red

blinking every 0.15 sec. &

Green

blinking

every 1 sec.

Upgrading firmware

Red

blinking every 0.15 sec. &

Green

blinking

every 0.15 sec.

Restoring default

Hardware Reset

The reset button is used to reset the system or to restore the factory default settings. Sometimes

resetting the system can return the camera to normal operation. If the system problems remain

after reset, restore the factory settings and install again.

Reset

: Press and release the reset button with a paper clip or thin object. Wait for the Network

Camera to reboot.

Restore

: Press and hold the reset button for at least ten seconds to restore system defaults.

Note that all settings will be restored to factory defaults.

SD/SDHC/SDXC Card Capacity

This network camera is compliant with

SD/SDHC/SDXC 32GB, 64GB,

and other preceding

standard SD cards.

DI-

DO+

DI+

DO-

Switch

External Device

Dry contact and using camera’s DO+ to supply a relay.

Relay

External AC power

with Protected Earth

Summary of Contents for SD9363-EHL













































































































































































































































































































































Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands

Vivotek SD9363-EHL, User Manual

Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands