Vivotek SD9363-EHL User Manual Download

Page: 32 / 332

VIVOTEK

32 - User's Manual

Pan /Tilt /Zoom /Focus speed

: Adjust the speed of Pan/ Tilt/ Zoom/ Focus:

Note that mouse screen control is also supported. You can refer to page 101 for related information.

Configuration Area

Client Settings

: Click this button to access the client setting page. For more information, please refer to

Client Settings on page 36.

Configuration: Click this button to access the configuration page of the Network Camera. It is suggested

that a password be applied to the Network Camera so that only the administrator can configure the

Network Camera. For more information, please refer to Configuration on page 41.

Language

: Click this button to choose a language for the user interface. Language options are available

in: English, Deutsch, Español, Français, Italiano,

日本語

, Português,

簡体中文

, and

繁體中文

. You can

also change a language on the Configuration page; please refer to page 41.

Hide Button

You can click the hide button to hide the control panel or display the control panel.

Pan speed

Tilt speed

Zoom speed

Focus speed

-5

Slower

Faster

-4

-3

-2

-1

Summary of Contents for SD9363-EHL













































































































































































































































































































































Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands

Vivotek SD9363-EHL, User Manual

Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands