Vivotek IB836BA-EHF3 User Manual Download

Page: 253 / 334

VIVOTEK

User's Manual - 253

"capability_image_c<n>_
scenemode_support" is 1

wbmode

auto,
manual,
rbgain,
widerange,
outdoor,indoor,
sodiumauto,
-

0/7

Available white balance mode.
"-" means white balance is not
supported.

iristype

piris,
dciris,
-

0/7

Indicate iris type.
"piris": P-Iris
"dciris": DC-Iris
"-": No Iris control support

* Note: For some cameras, this value
may be varied depending on mounted
lens.

sensortype

rawsensor,
smartsensor

0/7

Indicate sensor type.

"rawsensor"

: Raw sensor

"smartsensor"

: Smart sensor

* We support this parameter when the
version number (httpversion) is equal
or greater than 0302a.

exposure_mode

0,1

0/7

0: Non-support exposure control.
1: Support exposure control.

exposure_modetype

auto,
shutterpriority,
irispriority,
manual

0/7

Available mode of exposure setting.
* We support this parameter when the
version number (httpversion) is equal
or greater than 0302a.

exposure_rangetype

onevalue,
twovalues

0/7

Support interface of exposure range.

"onevalue"

: The parameter is a

constant value.

"twovalues"

: Need two parameters

to indicate the exposure range.

* We support this parameter when the
version number (httpversion) is equal
or greater than 0302a.

Summary of Contents for IB836BA-EHF3















































































































































































































































































































































Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Related manuals for IB836BA-EHF3

Brands by name

Popular brands

Vivotek IB836BA-EHF3, User Manual

Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Related manuals for IB836BA-EHF3

Brands by name

Popular brands