Vivotek IB836BA-EHF3 User Manual Download Page 231

Page: 231 / 334

VIVOTEK

User's Manual - 231

maxpanangle

0/7

The upper limit for pan angle.
*Only available when bit0 of
"capability_camctrl_c<0~(n-1)>_buildinpt" is
"1"

tiltspeedlv

0, <positive integer> 0/7

The maximum speed level of tilt motion.
*Only available when bit1 of
"capability_camctrl_c<0~(n-1)>_buildinpt" is
"1"

mintilt

0, <positive integer> 0/7

The lower limit for tilt position.
*Only available when bit1 of
"capability_camctrl_c<0~(n-1)>_buildinpt" is
"1"

maxtilt

0, <positive integer> 0/7

The upper limit for tilt position.
*Only available when bit1 of
"capability_camctrl_c<0~(n-1)>_buildinpt" is
"1"

mintiltangle

0/7

The lower limit for tilt angle.
*Only available when bit1 of
"capability_camctrl_c<0~(n-1)>_buildinpt" is
"1"

maxtiltangle

0/7

The upper limit for tilt angle.
*Only available when bit1 of
"capability_camctrl_c<0~(n-1)>_buildinpt" is
"1"

zoomspeedlv

0, <positive integer> 0/7

The maximum speed level of zoom motion.
*Only available when the value of
"capability_camctrl_c<0~(n-1)>_zoommodule"
is "1"

minzoom

0, <positive integer> 0/7

The lower limit for zoom position.
*Only available when the value of
"capability_camctrl_c<0~(n-1)>_zoommodule"
is "1"

maxzoom

0, <positive integer> 0/7

The upper limit for zoom position.
*Only available when the value of
"capability_camctrl_c<0~(n-1)>_zoommodule"
is "1"

maxdzoom

0, <positive integer> 0/7

The upper limit for digital zoom position.
*Only available when the value of
"capability_camctrl_c<0~(n-1)>_zoommodule"
is "1"

Summary of Contents for IB836BA-EHF3















































































































































































































































































































































Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Brands by name

Popular brands

Vivotek IB836BA-EHF3, User Manual

Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Brands by name

Popular brands