Vivotek IB836BA-EHF3 User Manual Download

Page: 202 / 334

VIVOTEK

202 - User's Manual

5150,
5900,
6700,
7400,
7950,
10200,
12200

* Only available if AMR is supported.

s0_g711_mode

pcmu,
pcma

4/4

Set G.711 companding algorithm.
pcmu: µ-law algorithm
pcma: A-law algorithm

* Only available if G.711 is supported.

s0_g726_bitrate

16000,
24000,
32000,
40000

4/4

Set G.726 encoded bitrate in bps.

* Only available if G.726 is supported

s0_g726_bitstreampackin
gmode

little, big

4/4

Set G.726 bit streaming packing mode.
little: Little-endian bitstream format.
big: Big-endian bitstream format.

* Only available if G.726 is supported.

s0_g726_vlcmode

0, 1

4/4

Enable vlcmode for G.726.
0: Standard mode.
1: Solve compatibility problem with VLC
player.

* Only available if G.726 is supported.

alarm_enable <boolean>

4/4

Enable audio detection

alarm_level

1~100

4/4

Audio detection alarm level

profile_i0_enable

4/4

Enable/disable this profile setting

profile_i0_policy night,

schedule

4/4

The mode which the profile is applied to.

* Not support "policy=day" anymore when the
version number (httpversion) is equal or
greater than 0301a.

profile_i0_begintime

hh:mm

4/4

Begin time of schedule mode.

profile_i0_endtime

hh:mm

4/4

End time of schedule mode.

Summary of Contents for IB836BA-EHF3















































































































































































































































































































































Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Related manuals for IB836BA-EHF3

Brands by name

Popular brands

Vivotek IB836BA-EHF3, User Manual

Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Related manuals for IB836BA-EHF3

Brands by name

Popular brands