Vivotek IB836BA-EHF3 User Manual Download

Page: 119 / 334

VIVOTEK

User's Manual - 119

Customized Script

This function allows you to upload a sample script (.xml file) to the camera, which will save your time on

configuring the settings. Please note that there is a limited number of customized scripts you can upload;

if the current amount of customized scripts has reached the limit, an alert message will prompt. If you

need more information, please contact VIVOTEK technical support.

20150213
20150213

Click to upload a file

Click to modify the

script online

Summary of Contents for IB836BA-EHF3















































































































































































































































































































































Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Related manuals for IB836BA-EHF3

Brands by name

Popular brands

Vivotek IB836BA-EHF3, User Manual

Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Related manuals for IB836BA-EHF3

Brands by name

Popular brands