Vivotek IB836BA-EHF3 User Manual Download Page 332

Page: 332 / 334

VIVOTEK

332 - User's Manual

8 m

80 mm

293 mm

Technical Specifications

Model

IB836BA-HT: Vari-focal, P-iris, Remote Focus

IB836BA-EHT: Vari-focal, P-iris, Remote Focus,
Extreme Weather

IB836BA-HF3: Fixed-focal

IB836BA-EHF3: Fixed-focal, Extreme Weather

System Information

CPU

Multimedia SoC (System-on-Chip)

Flash

1Gb

RAM

2Gb

Camera Features

Image Sensor

1/2.7" Progressive CMOS

Maximum Resolution

1920x1080 (2MP)

Lens Type

IB836BA-HT/EHT: Vari-focal, Remote Focus

IB836BA-HF3/EHF3: Fixed-focal

Focal Length

IB836BA-HT/EHT: f = 2.8 ~ 12 mm

IB836BA-HF3/EHF3: f = 3.6 mm

Aperture

IB836BA-HT/EHT: F1.8 ~ F2.85

IB836BA-HF3/EHF3: F2.1

Auto-iris

P-iris (IB836BA-HT/EHT)

Field of View

IB836BA-HT/EHT:

39° ~ 92° (Horizontal)

22° ~ 49° (Vertical)

45° ~ 122° (Diagonal)

IB836BA-HF3/EHF3:

83° (Horizontal)

53° (Vertical)

91° (Diagonal)

Shutter Time

1/5 sec. to 1/32,000 sec.

WDR Technology

WDR

Day/Night

Removable IR-cut filter for day & night function

Minimum Illumination

IB836BA-HT/EHT:

0.015 Lux @ F1.8 (Color)

0.001 Lux @ F1.8 (B/W)

IB836BA-HF3/EHF3:

0.016 Lux @ F2.1 (Color)

0.001 Lux @ F2.1 (B/W)

Pan/Tilt/Zoom
Functionalities

ePTZ:

48x digital zoom

(4x on IE plug-in, 12x built in)

IR Illuminators

Built-in IR illuminators,

effective up to 30 meters with Smart IR

IR LED*8

On-board Storage

Slot type: SD/SDHC/SDXC card slot

Seamless Recording

Video

Compression

H.264 & MJPEG

Maximum Frame Rate

30 fps @ 1920x1080

In both compression modes

Maximum Streams

4 simultaneous streams

S/N Ratio

70dB

Dynamic Range

110dB

Video Streaming

Adjustable resolution, quality and bitrate
Smart Stream

Image Settings

Adjustable image size, quality and bit rate; Time
stamp, text overlay, flip & mirror; Configurable
brightness, contrast, saturation, sharpness,
white balance, exposure control, gain, backlight
compensation, privacy masks; Scheduled profile
settings, 3D noise reduction, video rotation,
defog

Audio

Audio Capability

Two-way Audio (full duplex)

Compression

G.711, G.726

Interface

External microphone input

Audio output

Network

Users

Live viewing for up to 10 clients

Protocols

IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, RTSP/RTP/
RTCP, IGMP, SMTP, FTP, DHCP, NTP, DNS, DDNS,
PPPoE, CoS, QoS, SNMP, 802.1X, UDP, ICMP, ARP,
SSL, TLS

Interface

10Base-T/100 BaseTX Ethernet (RJ-45)

*It is highly recommended to use standard Cat.
5e & Cat. 6 cables which are compliant with the
3P/ETL standard.

ONVIF

Supported, specification available at

www.onvif.org

Intelligent Video

Video Motion Detection

Five-window video motion detection

VCA

Line crossing detection, field detection, loitering
detection

*Available per project request.

Alarm and Event

Alarm Triggers

Motion detection, manual trigger, digital input,
periodical trigger, system boot, recording
notification, camera tampering detection, audio
detection

Alarm Events

Event notification using digital output, HTTP,
SMTP, FTP, NAS server and SD Card

File upload via HTTP, SMTP, FTP, NAS server and
SD card

General

Smart Focus System

Remote Focus (IB836BA-HT/EHT)

Connectors

RJ-45 cable connector for Network/PoE
connection

Audio input

Audio output

DC 12V power input

Digital input*1

Digital output*1

LED Indicator

System power and status indicator

Power Input

DC 12V

IB836BA-HT/HF3:

IEEE 802.3af/at PoE Class 0

IB836BA-EHT/EHF3:

IEEE 802.3at PoE Class 4

Power Consumption

IB836BA-HT: Max. 13 W

IB836BA-EHT/EHF3: Max. 25 W (Heater on)

IB836BA-HF3: Max. 9 W

Dimensions

Ø 88 x 293 mm

Weight

Net: 1264 g

Casing

Weather-proof IP66-rated housing

(Camera body)

Vandal-proof IK10-rated metal housing

(Camera body)

Safety Certifications

IB836BA-HT/EHT:

CE, LVD, FCC Class A, VCCI, C-Tick, UL

IB836BA-HF3/EHF3:

CE, LVD, FCC Class A, VCCI, C-Tick

Operating Temperature

IB836BA-HT/HF3:

Starting Temperature: -10°C ~ 50°C

(14°F ~ 122°F)

Working Temperature: -20°C ~ 50°C

(-4°F ~ 122°F)

IB836BA-EHT/EHF3:

Starting Temperature: -40°C ~ 50°C

(-40°F ~ 122°F)

Working Temperature: -50°C ~ 50°C

(-58°F ~ 122°F)

Warranty

IB836BA-HT/EHT: 36 months

IB836BA-HF3/EHF3: 24 months

System Requirements

Operating System

Microsoft Windows 7/8/Vista/XP/2000

Web Browser

Mozilla Firefox 7~43 (Streaming only)

Internet Explorer 7/8/9/10/11

Other Players

VLC: 1.1.11 or above

Quicktime: 7 or above

Included Accessories

User's manual, quick installation guide,
Installation Wizard 2, VAST 32-channel recording
software

Others

Quick installation guide, warranty card, sun
shield, wall mount bracket, alignment sticker/
desiccant bag, waterproof connector, screw pack

Dimensions

Summary of Contents for IB836BA-EHF3















































































































































































































































































































































Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Brands by name

Popular brands

Vivotek IB836BA-EHF3, User Manual

Search results

Summary of Contents for IB836BA-EHF3

Reviews:

Brands by name

Popular brands