Vitek VT-3403 B, Manual Instruction

Page: 5 / 40

5
ENGLISH
WARNING: Before assembling, make sure
that the power plug is not inserted into the
mains socket.
−
Insert the whisk (7) into the gear (6).
−
Install the gear (6) on the motor unit (2) so
that the mark
▼
is opposite the mark .
Turn the motor unit clockwise till bumping.
The mark
▼
should match the mark in
fixed position.
−
Insert the power plug into the mains
socket.
−
Sink the whisk (7) into the bowl with
products.
−
Set the required operation speed using
the control knob (5). To switch the unit
on, press and hold the «I» button (4).
Use this operation mode for mixing liquid
products.
−
If you press and hold the «II» button (3),
the unit will operate at maximum rotation
speed.
−
After you finish using the unit, take the
power plug out of the mains socket and
disconnect the whisk (7) from the gear (6).
Remove the gear (6) from the motor unit
(2) turning it so that the mark
▼
is opposite
the mark .
Attention!
•
Do not use the whisk (7) to knead stiff
dough.
•
Products should be put into the bowl
before the unit is switched on.
USING THE CHOPPER
The chopper is used to chop meat, onion, herbs,
garlic, vegetables and fruits.
Attention!
•
Do not chop very hard products, such as
nutmegs, coffee beans and cereals.
Before you start chopping:
•
Remove bones, sinews and cartilage from
meat.
•
Cut meat, onion, garlic, carrots etc. into
approximately equal slices.
•
When chopping greens, remove stems of
herbs.
Chopping
WARNING: Before assembling the chopper,
make sure that the power plug is not inserted
into the mains socket.
Caution! The chopping knife (10) is very
sharp! Always hold the chopping knife (10)
only by the upper plastic end.
•
Set the chopping knife (10) on the axis (11).
•
Put the products into the bowl (9).
•
Place the geared lid (8) on the bowl (9) and
rotate the geared lid (8) clockwise until it is
fixed.
•
Connect the motor unit (2) to the geared lid (8)
matching the mark
▼
with the mark . Turn
the motor unit so that the mark
▼
is opposite
the mark .
•
Set the required operation speed with the
control knob (5). To switch the unit on, press
and hold the «I» button (4).
•
When the button (3) «II» is pressed, the unit
operates at maximal rotation speed.
•
During operation hold the motor unit (2) with
one hand and the chopper bowl (9) with the
other hand.
•
After using the chopper disconnect the motor
unit (2) from the geared lid (8) turning it so
that the mark
▼
is opposite the mark .
•
Remove the geared lid (8) rotating it counter-
clockwise.
•
Carefully remove the chopping knife (10) tak-
ing it by the upper plastic end.
•
Take the chopped products out of the chop-
per bowl.
Attention! Strictly follow the described
sequence of operations.
Maximal volume of the products to process
should not exceed 600 ml.
CLEANING
Attention! The blades of the chopping knife
(10) are very sharp and dangerous. Handle
the chopping knife (10) very carefully!
•
Unplug the unit before cleaning.
•
Remove the attachments.
•
Use a slightly damp cloth to clean the motor
unit (2) and the reduction gears (6, 8), then
wipe them dry.
•
After processing salty or sour products, it is
necessary to rinse the chopping knife (10)
and the detachable blender attachment (1)
with water right after use.
•
While possessing products with strong dye-
ing properties (for instance, carrot or beet-
root), the attachments and the bowls can get
colored; wipe them with a cloth dampened in
vegetable oil.
VT-3403_IM.indd 5 24.12.2013 10:37:48