11
Hardness gpg
10
15
20
25
30
35
40
45
50
55
60
65
70
Soft Water Available
(U.S. Gallons)
2250 1500 1125 900
750
643
563
500
450
409
375
346
321
Hardness gpg
10
15
20
25
30
35
40
45
50
55
60
65
70
Soft Water Available
(U.S. Gallons)
2613 1742 1306 1045 871
747
653
581
523
475
436
402
373
Hardness gpg
10
15
20
25
30
35
40
45
50
55
60
65
70
Soft Water Available
(U.S. Gallons)
2900 1933 1450 1160 967
829
725
644
580
527
483
446
414
Medium Salt Setting (table B):
Low Salt Setting (table A):
High Salt Setting (table C):
3. Set The Regeneration Time Of Day: The default regeneration time is set at 2:00 AM. If you want
to change the time for the regeneration cycle to start follow the steps below.
Step 1. If starting at In-Service display screen press Menu/Confirm key
to switch to main menu.
Step 2. Scroll down to “Advance Settings” in the main menu using the down arrow
.
Step 3. Press the Menu/Confirm Key
to enter the “advance settings” sub menu.
Step 4. Scroll down to “Setting Recharge Time” using the down arrow key
.
Step 5. Press the Manual/Confirm Key
. The hour will start flashing. Use the down and up arrow
keys
to scroll to the correct hour. The AM and PM will change as hours advance from
morning to afternoon. When the correct hour is chosen press Menu/Confirm Key
and the
flashing will advance to the minutes. Use the down and up arrow keys
to advance to
the correct minutes.
Step 6. Press the Menu/Confirm Key
will bring you back to “Setting Recharge Time”.
Step 7. Press the Manual/Return Key
twice to bring you back to the In Service Display screen.
4. Set Capacity (amount of soft water available):
The default capacity is 1306 U.S. Gallons @ 20 grains/U.S. Gallon at medium salt setting.
Step 1. If starting at In-Service menu press Menu/Confirm key
to switch to the main menu. If
continuing in the main menu scroll down to “Advance Settings” using the arrow keys
Step 2. If already in sub menu scroll down to “Residual Water Setting” using the arrow keys
Press the Menu/Confirm Key
to enter the “Advance Settings” sub menu.
Step 3. Scroll down to “Residual Water” in the sub menu set up using the down arrow key
.
Step 4. Press the Manual/Confirm Key
to enter the “Residual Water” setting.
Step 5. The capacity residual water volume number will be flashing. Input the water volume capacity
that corresponds to your water hardness. The water hardness was determined by you during
testing of the water that enters your facility. Refer to table on top of the valve under the top
cover or table B below. Use table to determine water volume capacity based on hardness.
Use the down and up arrow keys
to input the volume.
Step 6. Press the Manual/Confirm Key
. This will return you to the sub menu. If continuing to set up
other parameters like salt setting stay in the sub menu. If exiting sub menu proceed to Step 7.
Step 7. Press Manual/Return Key twice
to exit the set-up menu to the In-Service Display.
5. Salt Setting At Low, Medium and High:
The water softener default salt settings are at a medium salt setting of 8.0 lbs. of salt for every
regeneration cycle. The option exists for setting the salt setting to low and high salt setting. When the salt
setting is set to low (6.0 lbs. of salt) there will be less soft water available per regeneration cycle.
Therefore you will regenerate more frequently than at medium salt setting. When the salt setting is set at
high (14 lbs. of salt) there will be more soft water per regeneration cycle than low and medium setting.
