manualshive.com logo in svg

Vision Research Phantom v1211, Manual

Share
Download
Vision Research Phantom v1211 Manual Download Page 64

Phantom Ultrahigh-speed cameras Manual

58

Removing a CineMag II

The Phantom CineMag II clips into the MagMate of the 
Phantom as shown in the illustration to the left.

All the power and data connections are made between 
the pins on the MagMate and the pads of the Phantom 
CineMag II. Please be careful when attaching or removing 
the Phantom CineMag II that you don’t damage the pins 
on the camera. Avoid dragging the tabs on the front of the 
Phantom CineMag II across the pins.

To remove the Phantom CineMag II, pull the red tab on the 
back of the camera and lift the Phantom CineMag II, being 
careful not to damage the pins on the camera.

Saving from a CineMag II

In case damage to the pins occurs, Vision 
Research sells replacement pin-arrays that are 
easily installed in the field. 

Attaching a CineMag II

Vision Research recommends that you save the clips from 
a Phantom CineMag II as Cine Raw files, even though it 
is possible to save them in a number of file formats. Cine 
Raw files not only preserve all the metadata of the clip 
(such as frame rate, shutter speed, timestamps, etc.)  
it will also be the fastest and best-quality format.

Summary of Contents for Phantom v1211

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands