ViscoTec Preeflow eco-CONTROL EC200-K Operation And Maintenance Instructions Download Page 27

Page: 27 / 36

Dosing system eco-CONTROL EC200-K

Operation and maintenance instructions

Version 1.8

27 / 35

5.11

Creating dosing programs

Only possible when using a memory card, a diskette symbol appears in the display at the

lower right. If there is no memory card, then only program 00 (volatile memory) is

available.

The creation of a dosing program is done as part of the Save function by inputting a

dosing program number.
•   Select the dosing program (e.g. quantity program).
•   Set the values (quantity, flow rate, sucking back).
•   Save and input a dosing program number.

Use a memory slot that is still free so that no existing data is overwritten.

All the setting options for this dosing program are now available for editing. Do this as

described below under 5.13.

Error message SD chipcard

If the chipcard is defective or has not been inserted,

when the Dosing systems is switched on a

corresponding message (display 37) is shown for 3

seconds.

y 37

5.10

Clearing error messages

If there is an error message, it is shown flashing in the

status line (display 36) and an acoustic signal is given.

(if it has not been switched off, see

5.9.10, System and error messages, page 26)

• Press the

Info

key, the acoustic signal is switched off,

and the corresponding error message appears.

pla

• Correct the error and clear the error message with

Caution:

If the error message

Overcurrent switching

appears, the dispenser must be

cleaned before any further use.

Can´t find memory card.

10 47h

Fr 18.03.11

Fault

Esc

Suckback

Flow rate

Volume

100%

ml/min

00.100

03.000

00.000

Alarm messages

Quit

Over current shutdown!

Read manual!

Check dispenser!

Alarm messages

Quit

Check pressure!

Desired pr.

Actual pr.

1.0Bar

0.2Bar

Alarm messages

Quit

Level minimum

Check level!

Summary of Contents for Preeflow eco-CONTROL EC200-K





































Search results

Summary of Contents for Preeflow eco-CONTROL EC200-K

Reviews:

ViscoTec Preeflow eco-CONTROL EC200-K, Operation And Maintenance Instructions, Page: 27 / 36

Search results

Summary of Contents for Preeflow eco-CONTROL EC200-K

Reviews: