manualshive.com logo in svg

Vip-Vision Apartment Series, Installation Manual, Page: 11 / 54

Share
Download
Vip-Vision Apartment Series Installation Manual Download Page 11

11

Visit 

help.c5k.info

 for more information and support

Name

Description

Ethernet Port

Power over Ethernet & network connectivity

Reset Button

Reset configuration back to factory default settings

Tamper Switch

The Door Station will generate an alarm sound if it is being removed from the wall

8-Pin 
Connector

12V_OUT

12V DC positive output, 100ma max current (for use with the INTIPDM)

GND

Weigand card reader ground connection 

WG_D1

Weigand card reader D1 connection

WG_D0

Weigand card reader D0 connection

WG_LED

Weigand card reader LED connection

GND

Ground connection for 12V_OUT

RS485B

For use with the INTIPDM

RS485A

For use with the INTIPDM

12-Pin 
Connector

DC_IN 

12V DC positive input

GND

12V DC negative input

ALM_OUT_NO

Alarm output normally open contact

ALM_OUT_COM

Alarm output common contact

GND

Ground contact to be used with ALM_IN

ALM_IN

Alarm input contact

NO

Door relay normally open contact

COM

Door relay common contact

NC

Door relay normally closed contact

GND

Ground connection for SR or PUSH

PUSH

Exit button dry contact input, triggers door relay when shorted to GND

SR

Door latch feedback input, for use with monitored door latch

2.1 Connection Diagrams - Door Stations (cont.)

2.1.1  INTIPADSD - Apartment Series Door Station

Summary of Contents for Apartment Series























































Reviews:

No comments