background image

2

Features Overview

VIKING

©

INFO HELP

CALL

CONNECTED

Speaker Screen:

  Speaker screen with 

0.018" wide slots to prevent punctures 
from paperclips, etc.

Faceplate:

  Marine grade 316 stainless steel.

Speaker:

  Mylar speaker with rubber 

gasket to maintain water-tight seal and 
eliminate water deterioration.

Mounting Screws:

  (4) T-10 Torx head 

stainless steel, flat head, security 
screws and drive bit included.

Red Call Connected LED

Microphone:

  Omni-directional 

microphone with protective 
water-resistant cloth.

E

M

E

R

G

E

N
C

Y

CALL

CONNECTED

PUSH FOR

VIKING

©

HELP

“HELP” Push to Call Button:

  Solid 316 

stainless steel internally sealed per IP67.

“INFO” Push to Call Button 
(models E-1600A-AST2EWP 
and E-1600A-BLT2EWPonly):

  

Solid 316 stainless steel 
internally sealed per IP67.

Grade 2 Braille Label

Laser Etched Graphics

Mounting Screws:

  (4) T-10 Torx head stainless steel, 

flat head, security screws and drive bit included.

SL-2 Strobe/Beacon:

  Blue shatter resistant polycarbonate 

lens. Designed to meet IP66 ingress Protection Rating.

Tower Chassis:

  8 gauge (0.125” thick) aluminum with 

weather-resistant high-visibility yellow powder paint.

Rain Guard

(included)

EMERGENCY

 or 

ASSISTANCE

 lettered in 

black on three sides of the tower chassis.

Rear View of the 

Phone Panel

Ring Connector

(included)

* Earth Ground

(optional)

1600A Emergency Phone Board

BLK-4 Control Module

Marine grade 316 stainless steel faceplate 
and push button switch (sealed per IP67)

1

3

2

ON

1

2

ON

Front View of the

Phone Panel

Summary of Contents for E-1600A-AS T2EWP

















Reviews: