background image

9

The security code allows the user/installer to program the 

1600A 

series phone while DIP switch 

3

is in the 

ON

(normal)

position.  The factory set security code is 845464 (V-I-K-I-N-G).  It is recommended that the factory set security code
be changed.  

Example:

To store 123456 as the security code:

Enter Your Security Code Here:

#19

Note:

The security code must be 6 digits and cannot include a 

Q

or a 

#

.

The help speed dial number programmed in location 

#00

is the number that is

dialed when the “

HELP

” 

CALL

” button is first pressed.  Additional speed dial

numbers will be dialed when there is no answer or a busy signal is detected and
the next number redial features are activated. To program, enter the desired
speed dial number followed by the location number (

#00 - #04

).  To clear a speed

dial location, simply enter the memory location (

#00 - #04

) alone.  The 

1600A

series phone is factory set with no speed dial number programmed.

1.

HELP

/

CALL

”   

Speed Dial Numbers (memory locations #00 - #04)

Note:

Up to 20 digits can be stored in each dial position.  Special features such as pause, mode change, Touch Tone

Q

and 

#

count as single digits.

The Touch Tone I.D. number (up to 20 digits) is used by assistance personnel to identify the location of the caller and
is given out when the receiving party presses a Touch Tone 

Q

.  The security office can display the number using a Touch

Tone decoder.  To program the I.D. number, enter the desired number followed by 

#20

.  

Example:  

To store 333 as the

I.D. number, enter:

3 3 3 # 2 0

2. “INFO” Speed Dial Numbers (E-1600A-AST2EWP / E-1600A-BLT2EWP) (memory locations #07 - #09)

The information speed dial number programmed in location 

#07

is the telephone or extension number that is dialed

when the “

INFO

” button is first pressed.  Additional information speed dial numbers will be dialed when there is no

answer and the next number redial feature is activated.  The 

E-1600A-AST2EWP / E-1600A-BLT2EWP 

phone will

cycle through the programmed speed dial numbers until answered.  To program, enter the desired speed dial number
followed by the location number (

#07 - #09

).  To clear a speed dial location, simply enter the location (

#07 - #09

)

alone.

3. Speed Dial Programming Examples

E.  Identification Number

(memory location #20)

D.  Speed Dial Numbers

C.  Security Code

(memory location #19)

Step 1.

Access programming as shown is 

Programming

section 

A

.

Step 2.

Enter 

123456  #19

..

Step 3.

Hang-up..

To Program:

Enter:

Q

QQ

#

Q

#

4 second pause

Q

7

0, 1, 2 .... 9

0, 1, 2 .... 9

To Program the 1600A Series Phone...

Step 1 - 

See section A

Step 2 - Enter Digits:

...to store 555-1234 as the first speed dial number

Enter Programming

5 5 5 1 2 3 4 # 0 0

...to store a Touch Tone 9, a four second pause and then 333-
4444 into the second “Info” speed dial memory position

Enter Programming

Q

7 3 3 3 4 4 4 4 # 0 8

...to clear the first speed dial number

Enter Programming

# 0 0

Summary of Contents for E-1600A-AS T2EWP

















Reviews: