6)
Install sealed system access valves and recover refrigerant. After recovery, cap off valve.
7)
Remove electrical cover from side of compressor (See figures 12.9 & 12.10).
8)
Remove PTC starter and overload from compressor terminals.
9)
Heat joints and remove filter / drier.
10)
Heat joints and remove the discharge and suction lines at the compressor.
11)
It is advisable that the un-soldered copper tubes be capped if the system will be exposed to the
atmosphere for any length of time.
12)
Remove the lock nuts on the mounting plate and lift the compressor off the carriage bolts.
5.3.2 Installation of the new Compressor
1)
Do not remove the rubber plugs at the tube stubs on the compressor at this time.
2)
Install the four (4) rubber grommets onto the compressor base.
3)
Install the three sleeves where the carriage bolts are located.
4)
Mount the compressor into position on the mechanical base-plate.
5)
Install the three washers and lock nuts and tighten snuggly into place. Do not over tighten.
6)
Install and solder a new filter / drier.
7)
Remove rubber plugs from compressor tube stubs.
8)
Install and solder a new process tube to compressor.
9)
Install and solder the discharge line into compressor.
10)
Install and solder the suction line into compressor.
11)
Re-install PTC relay and overload to compressor terminals.
12)
Replace compressor electrical cover and snap into place.
13)
Carefully slide mechanical base plate assembly back under cabinet.
14)
Screw mechanical base plate assembly to cabinet (See figures 12.4 and 12.6).
15)
Evacuate, change, and leak check system.
16)
Replace front grille (See figure 12.5), back panel and power cord grommet (See figure 12.3).
SEE PHOTO SECTION FOR REFERENCE TO ABOVE MENTIONED FIGURES
28
2010 - Viking Preferred Service
SMR-0005
Summary of Contents for DFUW244CL
