66250675-EN - V1.0 - 05/09/17
45
4000 Series Vandal Resistant GSM - Technical Manual
4000 Series Vandal Resistant GSM Audio Intercom with Proximity Facility
Programming the GSM Intercom
• The DTP command sets the DTMF tone required (from 0 - 9) after a call is answered for button 1.
• The DTD command sets the DTMF tone required (from 0 - 9) after divert 1 call is answered for button 1.
• The DTT command sets the delay time from when the call is answered to when the DTMF is sent.
SET DTMF TONE REQUIRED FOR BUTTON 1 PRIMARY CALL
1111DTPn
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature
(for button 1).
1111DTPn?
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature.
Also send a confirmation text back to the sender with the stored DTMF tone setting (for
button 1).
SET DTMF TONE REQUIRED FOR BUTTON 1 DIVERT CALL
1111DTDn
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature
(for divert 1).
1111DTDn?
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature.
Also send a confirmation text back to the sender with the stored DTMF tone setting (for
divert 1).
SET THE DELAY TIME FROM WHEN THE CALL IS ANSWERED TO WHEN THE DTMF TONE IS SENT
1111DTTnn
Set the time nn, where nn = 01 - 12 seconds.
1111DTTnn?
Set the time nn, where nn = 01 - 12 seconds and also send a confirmation text back to the
sender of the time stored.
QUERY THE SETTINGS
1111DTP?
Query the DTMF tone set, replies TP = n.
1111DTD?
Query the DTMF tone set, replies TD = n.
1111DTT?
Query the delay time set, replies TT = nn.
ENABLE THE DIAL ‘0’ ON ANSWER FUNCTION (EDZ)
When enabled this feature allows an incoming call to be diverted to the programmed divert telephone number if the ‘0’ button on
the telephone has not been pressed after answering the call. This can be useful if the user’s number has an answerphone service (or
answer machine) and they do not want the call to be answered by this service or if the primary number (mobile no.) is switched off.
By default this function is disabled (set to 00). The following texts can be used to enable or disable this function.
1111EDZnn
Set the dial ‘0’ function nn: 01 or 00 (01 = enable, 00 = disabled).
1111EDZnn?
Set the dial ‘0’ function nn: 01 or 00 (01 = enable, 00 = disabled) also send a confirmation
text back to the sender.
1111EDZ?
Query the dial ‘0’ mode set.
When this feature is set the user answering the call must press ‘0’ on their phone to accept the call otherwise the call will be diverted
to the next number.
ENABLE THE # (HASH) FUNCTION (ED#)
Once enabled the end user must press the
#
button on their phone before pressing any other button (also refer to the user command
table on page 50) with the exception of when the user needs to enter the 4 digit programming code
“1111”
.
The user will have up to 3 seconds to press the user command button (e.g. button
3
to activate the relay), if the user doesn’t press
the next button within the 3 second window they will have to press the
#
button again.
By default this function is disabled (set to 00). The following texts can be used to enable or disable this function.
1111ED#nn
Set the # function nn: 01 or 00 (01 = enable, 00 = disabled).
1111ED#nn?
Set the # function nn: 01 or 00 (01 = enable, 00 = disabled) also send a confirmation text
back to the sender.
1111ED#?
Query the # mode set.
