Videx GSMVRK Technical Manual Download | Manualshive

Page: 60 / 60

background image

THE POWER TO SECURE

The product is CE marked demonstrating its conformity and is for distribution

within all member states of the EU with no restrictions. This product follows
the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU
(LVD); 2011/65/EU (RoHS): CE marking 93/68/ECC.

Main UK office:

VIDEX SECURITY LTD

1 Osprey Trinity Park
Trinity Way
LONDON E4 8TD
Phone: (+44) 0870 300 1240
Fax: (+44) 020 8523 5825
www.videxuk.com
[email protected]

Northern UK office:

VIDEX SECURITY LTD

Unit 4-7
Chillingham Industrial Estate
Chapman Street
NEWCASTLE UPON TYNE - NE6 2XX
Tech Line: (+44) 0191 224 3174
Phone: (+44) 0870 300 1240
Fax: (+44) 0191 224 1559

Greece office:

VIDEX HELLAS Electronics

48 Filolaou Str.
11633 ATHENS
Phone: (+30) 210 7521028

(+30) 210 7521998

Fax: (+30) 210 7560712

www.videx.gr
[email protected]

Danish office:

VIDEX DANMARK

Hammershusgade 15
DK-2100 COPENHAGEN
Phone: (+45) 39 29 80 00
Fax: (+45) 39 27 77 75
www.videx.dk
[email protected]

VIDEX ELECTRONICS S.P.A.

Via del Lavoro, 1 - 63846 Monte Giberto (FM) Italy
Tel (+39) 0734 631669 - Fax (+39) 0734 632475
www.videx.it - [email protected]

Benelux office:

VIDEX BENELUX

E3 Iaan, 93
B-9800 DEINZE
Phone: (+32) 9 380 40 20
Fax: (+32) 9 380 40 25
www.videx.be
[email protected]

Dutch office:

NESTOR COMPANY BV

Business Centre Twente (BCT)
Grotestraat, 64
NL-7622 GM Borne
www.videxintercom.nl
[email protected]

All Countries:

VIDEX ELECTRONICS S.P.A.

www.videx.it - [email protected]
Tel (+39) 0734 631669 - Fax (+39) 0734 632475

UK Customers:

VIDEX SECURITY LTD

www.videxuk.com - [email protected]
Tech Line: 0191 224 3174 - Fax: 0191 224 1559

MANUFACTURER

CUSTOMER SUPPORT

«
...
58
59
60

Summary of Contents for GSMVRK





























































Reviews:

No comments

Related manuals for GSMVRK

Brand: Datavideo Pages: 9

Brand: Datavideo Pages: 16

Brand: Gardi Systems Pages: 6

Brand: Phase Technology Pages: 11

Digital Movie DM 90.2

Brand: Canton Pages: 74

Brand: ICP DAS USA Pages: 2

Brand: Aiphone Pages: 2

Brand: Contec Pages: 65

Brand: Marco Pages: 3

Brand: Aiwa Pages: 80

Brand: Measurement Computing Pages: 27

Star Pulsar ESFR-25

Brand: Tyco Fire Product Pages: 4

Brand: National Instruments Pages: 4

Brand: Grundig Pages: 85

Brand: Panasonic Pages: 100

SHFX80 - WIRELESS SOUND SYSTEM

Brand: Panasonic Pages: 8

PELTOR ComTac 7

Brand: 3M Pages: 41

Brand: Sven Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands