background image

 

Two Wire Videokit ESVK Series

 

 PrtCode:ESVK_ENG_1.6.doc – Pag.8/44 

25/11/2009

Rev.1.6

SW2 – PRIVACY DURATION TIME 

Switches Status 

4 3 2 1 

Privacy Mode 

(switch 1) 

Privacy Duration 

(switches 2,3) 

OFF OFF 

15 minutes 

OFF ON 

1 hour 

ON OFF 

4 hours 

ON ON 

OFF 

The privacy duration time is set by switches 2 and 3. When enabled the privacy ser-
vice will be disabled when the set time expires or the switch is moved back to off. 

8 hours 

 

  ON 

No privacy time expiration: the privacy service is enabled or disabled only by the 
slide switch. 

 

 

 

SW3 – INTERCOMMUNICATION SETTINGS 

Switches Status 

4 3 2 1 

Intercommunication Mode 

(switch 1) 

Videophone 

Extension 

(switches 2,3) 

OFF OFF 

1 (master) 

OFF ON 

2 (slave) 

ON OFF 

3 (slave) 

ON ON 

OFF 

Intercommunication allowed between videophones (same unit address) inside the 
same flat. To call an extension pick up the handset then press the “door open” button 
as many times as the extension value (Eg. extension 2 two times, 3 three times etc). 

Each intercom/videophone in the same apartment must have a different exten-
sion address, the master address must always be set except when one of the 
intercom/videophone is set for apartment intercommunication (i.e. in a 3 inter-
com/videophone installation, one of the intercom/videophone must have the 
extension address 1 while the others must have different addresses)

 

4 (slave) 

 

OFF OFF ON 

Intercommunication allowed between videophones (different apartment). To call an 
extension pick up the handset then press the “door open” button as many times as 
the address value (Eg. extension 10 ten times, 12 twelve times etc) 

 

 

On installations where there are more than one intercom/videophone in the same apartment and intercommunication between different 
apartments is required, only one intercom/videophone may be set with this function (SW3.1=ON, SW3.2=OFF, SW3.3=OFF). The other inter-
com/videophones in the apartment must be set for local intercommunication with extension addresses “2-4” (slaves). From the inter-
com/videophone set for intercommunication with other apartments it will be not possible to intercommunicate within the apartment but slave 
extensions 2-4 will be able to intercommunicate with each other. 

 

NUMBER OF RINGS 

The number of rings can be set to 3 (factory preset) or 6. 
To change the number of rings proceed as follow: 

Disconnect the power supply from the system; 

Short the terminals “LB” and “GND”; 

Reconnect the power supply to the system checking the privacy on LED and then remove the short between terminals “LB” and “GND”; 

The number of LED flashes will be 1 for 3 rings or 2 for 6 rings. 

Each time this operation is carried out the number of rings is switched between the values 3 and 6. 

 
 

SIGNALS ON CONNECTION TERMINALS 
Signal Description 
BUS 
BUS 

Bus contacts 

LED- 

Door open LED ground signal input 

LED+ 

Door open LED power supply input (+12Vdc) 

GND 

Ground signal 

GND 

Ground signal 

AL 

Alarm input (not implemented) 

LB 

Local Bell contact (put a push button between this terminal and the relevant GND terminal) 

 

 
 
 
 
 
 

SPECIFICATION 

Housing/Mounting 

3000 Series Intercoms / direct wall mounting 

Push Buttons 

Yes, two 

Programming 

Yes, carried out by the dip-switches inside the intercom 

Controls 

Call tone volume and privacy ON-OFF switch 

Power Supply 

Supplied by the BUS line 

Working Temperature 

-10 +50ºC 

 

 
 

CUSTOMER SUPPORT INFORMATION 

All Countries Customers 

UK Customers 

VIDEX Electronics S.p.A. 

www.videx.it

 – 

[email protected]

 

Tel.+39 0734 631669 

Fax +39 0734 632475 

VIDEX Security LTD 

www.videx-security.com

 

Tech Line 0191 224 3174 

Fax 0191 224 1559 

 

 

 

The product is CE marked demonstrating its conformity and  is for distribution within all 
member states of the EU with no restrictions. 
This product follows the provisions of the European Directives  
89/336/EEC & 92/31/EEC (EMC),  
73/23/EEC (LVD) and 93/68/EEC (CE marking). 

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribuito 
liberamente all’interno dei paesi membri dell’unione europea EU. 
Questo prodotto è conforme alle direttive Europee 
89/336/EEC & 92/31/EEC (EMC), 
73/23/EEC (LVD) e 93/68/EEC (Marcatura CE). 

 

Summary of Contents for 2 Wire













































Reviews: