Victaulic VE106 Groove-N-Go Operating And Maintenance Instruction Manual Download Page 24 | Manualshive

Page: 24 / 35

background image

VE106 Groove-N-Go Tool

23

6.

Install the lock washer, and tighten the

3

/

8

-inch hex bolt to retain the drive key.

MAINTENANCE

This section provides information about keep-
ing tools in proper operating condition and
guidance for making repairs, when neces-
sary. Preventive maintenance during opera-
tion will pay for itself in repair and operating
savings.

Replacement parts must be ordered from
Victaulic Tool Company to ensure proper and
safe operation of the tool.

LUBRICATION

1.

After every 2 hours of operation, apply a

No. 2EP lithium-base grease to the feed
screw. Apply the grease by hand to the screw
threads or through the grease fitting located
at the feed screw. Keep the feed screw lubri-
cated to ensure a long service life.

DANGER

• Before performing any mainte-

nance on the tool, disconnect
the power cord from the electri-
cal source.

Failure to follow this instruction
could result in death or serious
personal injury.

TM-VE106 3736 Rev_B.fm Page 23 Monday, May 9, 2005 12:02 PM

«
...
22
23
24
25
26
...
»

Summary of Contents for VE106 Groove-N-Go




































Reviews:

No comments

Related manuals for VE106 Groove-N-Go

Brand: Laser Pages: 8

Brand: B&B Pages: 3

Brand: Hammer Pages: 40

Brand: JAMEC PEM Pages: 4

Brand: BGS technic Pages: 12

Brand: Ironton Pages: 21

Start-It VEC025MB

Brand: Vector Pages: 8

Brand: Solaric Pages: 16

Portable AC-to-DC Regulated Power Supply

Brand: Radio Shack Pages: 28

Brand: Liebert Pages: 28

Brand: Vector Pages: 15

Brand: Gardena Pages: 14

Brand: Puls Pages: 2

Brand: Kennedy Pages: 2

Carlyle Tools 6-711A

Brand: Napa Pages: 16

Brand: RAMSET Pages: 14

Brand: Ulvac Pages: 89

All Day Battery Ride-On 7700

Brand: National Pages: 89

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands