manualshive.com logo in svg

Vicon Pilot Lite V1522, Installation And Operation Manual

Share
Download
Vicon Pilot Lite V1522 Installation And Operation Manual Download Page 54

3-14

  |

Chapter 3 Configuration 

 

XX196-00 

Pilot Lite 

 

Keypads 

You can define up to 8 keypads in the system. To begin, access the Control 
Keypads screen by selecting it from the menu bar or by double-clicking it in 
the system summary. The Keypads Groups and Keypad/Monitors Partitions 
menus are also referenced in this section.  

The keypads are listed by number in the Keypad # column. The parameters 
that can be set for each keypad are contained in the field columns, which are 
described in the following table. A description of each field parameter is 
displayed on the screen when the field is selected. 

Field Description 

Alarm Ack  

Selecting Enabled or Disabled will enable or disable 
the keypad’s ability to acknowledge an alarm.   

Default Monitor 

This setting defines the monitor that will automatically 
be selected at the specified keypad when the system 
is initially powered or rebooted. The default monitor 
must be a monitor partitioned to the keypad currently 
selected. See the Keypad/Monitor Partitions screen 
description for more information.   

Summary of Contents for Pilot Lite V1522











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands