Vicon Pilot Lite V1522 Installation And Operation Manual Download Page 114

Page: 114 / 138

3-74

Chapter 3 Configuration

XX196-00

Pilot Lite

2. Upon selection, the title below Available Field will change to the

parameter selected and the appropriate values will display in the
selection box.

3. Select All for all, Selected Only for an item that is highlighted in the

list or From to specify a range.

4. Click Update to implement the changes.

Note:

The Settings box contains two buttons: Apply and Restore. Clicking

Apply will make the changes permanent. Clicking Restore will cancel the
changes that you have made and revert back to the original values. Once
you click Apply, you cannot restore the original values.

Summary of Contents for Pilot Lite V1522











































































































































Search results

Summary of Contents for Pilot Lite V1522

Reviews:

Related manuals for Pilot Lite V1522

Brands by name

Popular brands

Vicon Pilot Lite V1522, Installation And Operation Manual

Search results

Summary of Contents for Pilot Lite V1522

Reviews:

Related manuals for Pilot Lite V1522

Brands by name

Popular brands