manualshive.com logo in svg

Vicon Pilot Lite V1522, Installation And Operation Manual

Share
Download
Vicon Pilot Lite V1522 Installation And Operation Manual Download Page 12

1-2

  |

Chapter 1 Introduction 

 

XX196-00 

Pilot Lite 

 

General Information 

 

The Vicon® Pilot Lite™ V1522 Matrix Switching and Control System provides 
control of CCTV systems of up to 32 cameras by 8 monitors. Everything you 
need to connect cameras, monitors, keypads, receivers and alarms is 
contained in a single unit. Programming the system is accomplished using 
the built-in Configurator.  

The Configurator provides an intuitive graphical user interface that enables 
you to set up system parameters, such as: 

ƒ

  Timed or Triggered Event Programming 

ƒ

 Keypad 

Setup 

ƒ

  Receiver Profile Configuration 

ƒ

 Camera 

Setup 

ƒ

  Titling and Identification of Cameras, Monitors and Presets 

ƒ

 Monitor 

Setup 

ƒ

  Salvo and Tour Configuration 

ƒ

  Alarm Processing Configuration 

The Pilot Lite has been configured with system defaults that should satisfy 
most installations with no need for further customization. For many users, it 
might not be necessary to modify the configuration with the Configurator.  

Summary of Contents for Pilot Lite V1522











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands