Vetus M2.02 Operation Manual Download Page 97

Page: 97 / 120

9 Troubleshooting

Fault finding table

6 Engine overheats

Possible fault

Remedy

Faulty injector/injection pump.

Check, replace if required.

Sea cock closed.

Open.

Raw water strainer clogged.

Check / clean.

Faulty raw water pump impeller. Check / replace.

Leak in raw water feed system.

Check / replace.

Coolant level too low.

Check / top up.

Faulty coolant pump.

Check / replace.

Faulty thermostat.

Check / replace.

Leak in coolant circuit .

Check.

Heat exchanger dirty or clogged
as a result of rubber particles
from a worn impeller.

Check / clean.

Oil level too low.

Increase level.

Oil level too high.

Lower level.

Faulty oil filter.

Replace.

Insufficient intake air.

Check / replace air intake filter.

Motor becomes apparently
overheated as a result of faulty
temperature switch, sensor or
meter.

Check / replace.

7 Engine not firing on all cylinders

Possible fault

Remedy

Fuel supply line restricted.

Check / clean.

Fuel filter clogged with water
and/or contamination.

Check or replace.

Faulty injector/injection pump.

Check, replace if required.

Leaking fuel supply line or fuel
injection line.

Check / replace.

Air in fuel system.

Check and bleed.

Faulty glow plugs.

Check / replace.

Incorrect valve clearance.

Adjust.

Summary of Contents for M2.02

























































































































Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands

Vetus M2.02, Operation Manual

Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands