Vetus M2.02 Operation Manual Download

Page: 51 / 120

6 Maintenance

Engine oil change

Every 100 operating hours.

16 Oiling the oil seal

• Clean the contact surface of the gasket.

• Lubricate the oil seal of the new filter ele-

ment with clean engine oil.

17 Oil filter installation

• Install the filter in accordance with the in-

structions printed on the filter element
housing.

18 Refilling with oil

• Refill the engine with new oil (for specifica-

tion see page

106

) through the filler open-

ing in the valve cover.

• Operate the engine at idling speed for a

short period of time. Check for oil leaks
whilst the engine is running. Stop the en-
gine. Allow 5 minutes for the oil to return
to the sump. Check the oil level with the
dipstick.

VD01011

VD00124

VD01013

mount

oil

(

oil

filter

inCl

: 2.9 litres

(5.1 Imp. pt, 6.1 US pt)

filter

art

Code

: STM0051

Summary of Contents for M2.02

























































































































Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands

Vetus M2.02, Operation Manual

Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands