Vetus M2.02 Operation Manual Download Page 64

Page: 64 / 120

6 Maintenance

Checking the V-belt

Every 500 operating hours.

38 Inspection V-belt

• Inspect the belt for wear and tear (fraying

and cracking). Belts which are in poor con-
dition should be replaced.

39 Checking tension

• Check tension of the V-belt by applying

moderate finger and thumb pressure. If the
deflection of the belt is more than 12 mm
(1/2”), using about 10 kg (20 lbs) thumb
pressure, it should be tensioned.

40 Tensioning V-belt

• Loosen the bolt of the adjustment bracket

and both the alternator mounting bolts.
Now push the alternator outwards until the
belt tension is correct.

• Now first re-tighten the upper mounting

bolt of the alternator.

• Then re-tighten the bolt of the adjustment

bracket and the lower mounting bolt.

VD00128

VD00034

VD00129

anger

Check, tension and change belts only with the
engine off. Refit belt guard, if provided.

V-

belt

art

Code

STM7369

Summary of Contents for M2.02

























































































































Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands

Vetus M2.02, Operation Manual

Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands