Vetus M2.02 Operation Manual Download Page 104

Page: 104 / 120

102

Model

M2.02

M2.06

Oil lubrication system

Oil capacity, max.

without oil filter

2.4 litres (4.2 Imp. pt, 5.1 US pt)

with oil filter

2.9 litres (5.1 Imp. pt, 6.1 US pt)

Oil Filter

Vetus STM0051

Oil temperature in sump

max. 130°C (266°F)

Cooling system

Capacity, Intercooler version

2.2 litres (3.9 Imp. pt, 4.6 US pt)

Keel cooler version, engine only

3 litres (5.3 Imp. pt, 6.3 US pt)

Thermostat

opening at 71°C (160°F), fully opened at 84°C (183°F)

Coolant pump,

Flow at max. engine rpm

50 l/min (11 Imp. Gal/min, 13.2 US Gal/min)

Total head keelcooler at max. flow

2 m Water (6’ 7”)

Inlet connection for hose keelcooler

28 mm (1

”) I.D.

Raw water pump,

Flow at max. engine rpm

20 l/min (4.4 Imp. Gal/min, 5.3 US Gal/min)

Total head at max. flow

2 m Water (6’ 7”)

Impeller

Vetus STM6161

Inlet connection for hose

20 mm (

”) I.D.

Heater supply connection

10 mm (

”)

Heater return connection

8 mm (

”)

10 Technical data

Engine specifications

Summary of Contents for M2.02

























































































































Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands

Vetus M2.02, Operation Manual

Search results

Summary of Contents for M2.02

Reviews:

Related manuals for M2.02

Brands by name

Popular brands