background image

109

9  Troubleshooting 

Fault finding table 

3 Engine cranks but will not start, smoke from exhaust

Possible fault

Remedy

Faulty injector/injection pump. Check, replace if required.
Faulty injector/injection pump. Check, replace if required.
Air in fuel system.

Check and bleed.

Wrong fuel quality or contami-
nated fuel.

Check fuel. Drain and flush fuel 
tank. Replace with new fuel.

Incorrect injection timing.

Check / adjust.

Setting of stop valve incorrect. Check / adjust.
Incorrect lube oil SAE class or 
quality for ambient tempera-
ture.

Replace.

Faulty glow plugs.

Check / replace.

Insufficient intake air.

Check.

Intake air filter clogged .

Clean/replace 

Incorrect valve clearance.

Adjust.

4 Engine starts but runs unevenly (rough idling) or 

stalls

Possible fault

Remedy

(Nearly) Empty fuel tank.

Refill.

Fuel supply line restricted.

Check / clean.

Fuel filter clogged with water 
and/or contamination.

Check or replace.

Vent line of fuel supply tank 
clogged.

Check / clean.

Faulty injector/injection pump. Check, replace if required.
Leaking fuel supply line or fuel 
injection line.

Check / replace.

Air in fuel system.

Check and bleed.

Wrong fuel quality or contami-
nated fuel.

Check fuel. Drain and flush fuel 
tank. Replace with new fuel.

Low battery voltage 

Recharge /replace 

Exhaust restricted.

Check.

Incorrect valve clearance.

Adjust.

Idle setting too low.

Check/ adjust.

Summary of Contents for DT4.70

















































































































































Reviews: