manualshive.com logo in svg

Vetus DT4.70, Operation Manual

Share
Download
Vetus DT4.70 Operation Manual Download Page 27

25

3  First commissioning

Filling coolant system, 

7 

interCooling

, 

if a water heater is connected (2)

The 

highest

  point  of  the  water  heater  is 

situated at a 

higher

 level than the expan-

sion tank for the ship’s engine.

The  water  heater  will 

not

  be  filled  and 

bled  automatically  during  filling  of  the 
cooling system.

Fill the cooling system via the expansion 

• 

tank (3).

Open valve (4) during filling and bleed-

• 

ing the system.

Unscrew plug (2), on top of the lid of the 

• 

thermostat housing, a few turns to bleed 
the system properly.

Tighten plug (2) after the cooling system 

• 

has  been  filled  and  bled  and  continue 

filling.

  n

ote

 

Remember to close valve (4) after filling 

• 

the system.

1

2

3

4

1.5 bar

DO NOT OPEN

VD00877

Use a mixture of 40% antifreeze (ethylene 
glycol based) and 60% tap water or use a 
special coolant.

For specifications see page 

127

.

  C

aution

Never fill the cooling system with sea water 
or brackish water.

Summary of Contents for DT4.70

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands