manualshive.com logo in svg

Vetus DT4.70, Operation Manual

Share
Download
Vetus DT4.70 Operation Manual Download Page 120

118

Model

:

DT4.70

DTA4.85

Oil lubrication system

Oil capacity, max. 

:

without oil filter

:

6.0 litres (10.6 UK pt, 12.7 US pt)

with oil filter

:

6.3 litres (11.1 UK pt, 13.3 US pt)

Oil Filter

:

08-00085

Oil temperature in sump

:

max. 120°C (248°F)

Cooling system

Capacity

:

8.0 litres (14.1 UK pt, 16.9 US pt)

Thermostat

:

opening at 82°C (180°F), fully opened at 97°C (207°F)

Coolant pump,
Flow at max. engine rpm

:

135 litres/min (29.7 UK gal/min, 35.7 US gal/min)

Raw water pump,
Flow at max. engine rpm

:

80 litres/min (17.6 UK gal/min, 21.1 US gal/min)

Total head at max. flow

:

2 metre (6’ 7”) H2O

Impeller

:

STM8074

Inlet connection for hose

:

28 mm (1 1/8") I.D.

Heater supply connection

:

16 mm (5/8") I.D.

Heater return connection

:

16 mm (5/8") I.D.

10 Technical data

Engine specifications

Summary of Contents for DT4.70

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands