manualshive.com logo in svg

Vetus DT4.70, Operation Manual

Share
Download
Vetus DT4.70 Operation Manual Download Page 129

127

Coolant fluid 

The preparation and monitoring of coolant in inter-cooled engines 
is especially important because corrosion, cavitation and freezing 
can lead to engine damage. Use as coolant a mixture of a cooling 
system protective liquid (anti-freeze, ethylene glycol based) and 
tap water.

In tropical climates, where anti-freeze availability may be limited, 
use a corrosion inhibitor to protect the engine cooling system. 

The  concentration  of  the  cooling  system  protective  liquid  in  the 
coolant should not fall below/exceed the following limits: 

Cooling system protective 

liquid (Anti-freeze)

Water

Protection against 

freezing to 

max. 45 vol% 

-35°C (-31°F) 

55%

40 vol% 

-28°C (-18°F) 

60%

min. 35 vol% 

-22°C (-8°F) 

65%

The protective liquid concentration must be maintained under all 
circumstances. Therefore if coolant must be added always use the 
same mixture of anti-freeze 
and tap water.

Water quality for coolant preparation 

Use preferably tap water. 

If available fresh water is used; the values given below must not 
be exceeded. 

Water quality

min.

max. 

pH-value at 20°C (68°F)

6.5 

8.5

Chloride ion content

[mg/dm

3

]

-

100

Sulphate ion content

[mg/dm

3

]

-

100

Total hardness 

[degrees] 

3

12

  C

aution

Never use sea-water or brackish water.

  W

arning

Cooling  system  protective  liquids  must  be  dis-
posed of in accordance with environmental regu-
lations.

11 Operating media

Coolant 

Summary of Contents for DT4.70

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands