Vetus DT4.70 Operation Manual Download Page 6

Page: 6 / 144

1 Safety measures

anger

Indicates that great potential danger exists
that can lead to serious injury or death.

arning

Indicates that a potential danger that can
lead to injury exists.

aution

Indicates  that  the  usage  procedures,  ac-
tions etc. concerned can result in serious
damage  to  or  destruction  of  the  engine.
Some  CAUTION  indications  also  advise
that a potential danger exists that can lead
to serious injury or death.

ote

Emphasises important procedures, cir-
cumstances etc.

Symbols

Indicates that the relevant proce-
dure must be carried out.

Indicates that a particular action is
forbidden.

Pass the safety precautions on to other
people who will use the engine.

General rules and laws concerning safety
and accident prevention must always be
observed.

Warning indications
The following warning indications are used
in this manual in the context of safety:

Warning indications

Summary of Contents for DT4.70

















































































































































Search results

Summary of Contents for DT4.70

Reviews:

Brands by name

Popular brands

Vetus DT4.70, Operation Manual

Search results

Summary of Contents for DT4.70

Reviews:

Brands by name

Popular brands