Vetus DT4.70 Operation Manual Download Page 116

Page: 116 / 144

114

9 Troubleshooting

Fault finding table

11 Black exhaust smoke (idling)

Possible fault

Remedy

Injector fault

Check /replace.

Oil level too high.

Lower level.

Excessive inclination of en-
gine.

Check / Adjust.

12 Blue exhaust smoke (idling)

Possible fault

Remedy

Oil level too high.

Lower level.

Leaking from turbo compres-
sor oil seal.

Check / replace oil seal.

13 Black exhaust smoke (at load)

Possible fault

Remedy

Faulty injector / injection
pump.

Check / replace if required.

Incorrect injection timing.

Check / adjust.

Oil level incorrect.

Check .

Insufficient intake air, air filter
dirty.

Check/clean the filter .

Leak in inlet manifold.

Check / replace.

Intercooler dirty.

Check/clean.

Incorrect valve clearance.

Adjust.

Excessive wear of cylinder /
piston.

Check compression; refurbish
engine.

Faulty turbo compressor.

Check / replace.

VGT Turbocharger actuator
blocked

Unblock /replace

Engine overloaded, max. rpm
is not reached.

Check sizes of propeller.

Engine overloaded.

Check size of propeller.

Summary of Contents for DT4.70

















































































































































Search results

Summary of Contents for DT4.70

Reviews:

Brands by name

Popular brands

Vetus DT4.70, Operation Manual

Search results

Summary of Contents for DT4.70

Reviews:

Brands by name

Popular brands