VESPA LX 50 Workshop Manual Download Page 61

Page: 61 / 160

Automatic transmission

Transmission cover

- Loosen the 15 screws and remove the transmis-

sion cover with the aid of a mallet.

N.B.

THE CRANKCASE IS SLIGHTLY BLOCKED BY THE TIGHT
FIT BETWEEN THE SHAFT OF THE DRIVEN HALF-PULLEY
AND THE BEARING HOUSED ON THE CRANKCASE.

Kickstart

- Remove the screws shown in the figure and re-

move the engine starting lever.

- For the assembly, work in reverse and tighten the

screws to the prescribed torque..

Locking torques (N*m)

Starter lever replacement

12 to 13 Nm

- Upon refitting, apply the recommended grease to

the bushing, to the spring and along the toothed

sector.

- Use the special tool for the charging of the spring,

as shown in the figure.

- Refit the seeger ring after checking that it is in

good condition.

Specific tooling

020261Y

Starter spring fitting

Recommended products

AGIP GREASE MU3

Grease for odometer

transmission gear case

Soap-based lithium grease with NLGI 3; ISO-L-

XBCHA3, DIN K3K-20

Vespa LX 50

Engine

ENG - 61

Summary of Contents for LX 50

































































































































































Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands

VESPA LX 50, Workshop Manual

Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands