VESPA LX 50 Workshop Manual Download Page 37

Page: 37 / 160

- If the parameters found do not agree with the above figures, act upon the idle adjusting screw. Oth-

erwise, check the automatic choke device

Specific tooling

020320Y

Exhaust gases analyser

020332Y

Digital rpm indicator

SAS filters inspection and cleaning

Remove the right side fairing by undoing the 2

screws marked «

» indicated in the figure.

Remove the two screws «

» from the aluminium

SAS cover. Release the metal tube from the rub-

ber housing on the cover without extracting the

tube from the cover/sleeve. Remove the tab and

plastic cover, extract the sponge and wash it in

water and soap. Dry it with compressed air before

refitting it, making sure to correctly fit the tab in the

housing on the two plastic and aluminium covers.

Every time you disassemble the filter, replace the

O-ring seal located in the cover.

Vespa LX 50

Maintenance

MAIN - 37

Summary of Contents for LX 50

































































































































































Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands

VESPA LX 50, Workshop Manual

Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands