VESPA LX 50 Workshop Manual Download Page 103

Page: 103 / 160

- Remove the fifth wheel fitting and the dust guard

on the steering tube as shown in figure, using the

specific tool. Proceed giving a few taps with the

mallet.

Specific tooling

020004Y

Punch for removing fifth wheels from

headstock

- Refit the fifth wheel fitting and the dust guard on

the steering tube until they stop, using the specific

tool.

Specific tooling

006029Y

Punch for fitting fifth wheel seat on

steering tube

Rear

Removing the rear wheel

- Use a screwdriver as a lever between the drum

and the cover.

-Straighten the split pin and remove the cap.

-Remove the wheel acting on the central fixing

point.

WARNING

-ALWAYS USE NEW SPLIT PINS FOR REFITTING.

Vespa LX 50

Suspensions

SUSP - 103

Summary of Contents for LX 50

































































































































































Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands

VESPA LX 50, Workshop Manual

Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands