VESPA LX 50 Workshop Manual Download Page 77

Page: 77 / 160

Removing the flywheel magneto

- Lock the rotation of the flywheel using the calliper

spanner.

- Remove the nut.

CAUTION

THE USE OF A CALLIPER SPANNER OTHER THAN THE
ONE SUPPLIED COULD DAMAGE THE STATOR COILS

- Extract the flywheel with the extractor.

Specific tooling

020565Y

Flywheel lock calliper spanner

020162Y

Flywheel extractor

Inspecting the flywheel components

- Check the condition of the flywheel and any dis-

tortions that might cause rubbing on the stator and

on the Pick-Up.

Refitting the flywheel magneto

- Fit the flywheel being careful to insert the key

properly.

- Lock the flywheel nut at the prescribed torque

- Check the Pick-Up air gap.

- The air gap may not be modified in the fitting of

the Pick-Up.

- Other values derive from deformations visible on

the Pick-Up support.

Vespa LX 50

Engine

ENG - 77

Summary of Contents for LX 50

































































































































































Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands

VESPA LX 50, Workshop Manual

Search results

Summary of Contents for LX 50

Reviews:

Related manuals for LX 50

Brands by name

Popular brands