VESALA PK2 User Manual Download

Page: 19 / 22

19 (22)

User Manual Vesala PK2 Receiver X2.0 ENG

5.3

Troubleshooting

If case of trouble, follow the table below for possible remedy.

Problem

Possible explanations

Remedy

The device does
not power up or
unexpectedly shuts
down.

One or more battery is
empty.

Replace all batteries.

One or more battery is
reversed.

Orient batteries so that polarity matches
markings on the battery compartment.

Device shuts down after
inactivity.

When no signal is detected, the device
will shut down after 10 minutes.

Receiver gives
inaccurate
positioning result
or indicates
distance
incorrectly.

There are interfering
objects nearby.

Stay clear from objects or use the offset
measurement method.

Transmitter PKT2 and
receiver PKR2 are not on
parallel planes.

Make sure that the structure is evenly
thick and place transmitter and receiver
accurately on their surfaces.

Summary of Contents for PK2























Search results

Summary of Contents for PK2

Reviews:

Related manuals for PK2

Brands by name

Popular brands

VESALA PK2, User Manual

Search results

Summary of Contents for PK2

Reviews:

Related manuals for PK2

Brands by name

Popular brands