VESALA PK2 User Manual Download | Manualshive

Page: 18 / 22

background image

User Manual Vesala PK2 Receiver X2.0 ENG

18 (22)

5

Taking care of your equipment

5.1

Storing

Remove batteries before storing the device for an extended period. Batteries left in the device
may leak and cause damage. Store the device, batteries and accessories inside its original
packaging in a dry, warm place.

5.2

Cleaning

If the device is dirty or wet, clean and dry the outer surface of the device with a soft cloth before
changing batteries. Avoid getting dirt or water inside the device. A small amount of isopropanol
can be used to remove stains and disinfect the surface. Battery compartment and battery
contact surfaces inside the battery compartment should only be cleaned with isopropanol and a
soft, lint free cloth.

«
...
16
17
18
19
20
...
»

Summary of Contents for PK2























Reviews:

No comments

Related manuals for PK2

Brand: XIEGU Pages: 48

Brand: XIEGU Pages: 13

Brand: Quark-Elec Pages: 2

Brand: Xoro Pages: 10

Brand: Yaesu Pages: 15

Brand: Chiayo Pages: 8

Brand: C & K Systems Pages: 2

Brand: Kramer Pages: 35

Brand: Shadow Pages: 6

Brand: VDO Pages: 14

Brand: Boss Audio Systems Pages: 23

AN/PRC-117D Series

Brand: Harris Pages: 40

Brand: Power Acoustik Pages: 45

Brand: Maxon Pages: 42

Brand: Pansat Pages: 28

Brand: GME Electrophone Pages: 28

Brand: Aiwa Pages: 20

Brand: SunVote Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands