Vermont Castings RFSDV34 Installation Instructions And Homeowner'S Manual Download

Page: 31 / 36

RFSDV34 Freestanding Direct Vent Gas Stove

10003550

FK24 Fan Assembly

This auxiliary fan system increases the efficiency of the

circulation of the heating air.
The FK4 fan kit allows variable speed control of the

circulation fan and also incorporates a heat sensor in the

circuit.

Specifications

115 Volt / 60Hz / 56 Watts

Maintenance

The fan itself does not require regular maintenance,

however periodic cleaning of the fan and the surrounding

area is required.
Check the fan and the area around the fan assembly and

wipe or vacuum at least once per month during the operating

season.

Installation
NOTE: The FK24 is an option for Model RFSDV24;

standard with model RFSDV34. Install fan before

connecting gas line to stove.

1. Open front access door; remove the cover valve.
. Remove pre-mounted fan bracket at the rear of the

pedestal. Remember this location for reinstallation.

3. Open the fan kit; mount FK4 replacement fan bracket.

(Fig. 47)

4. Install the fan through the opening of the front access

door, with the outlet pointed up and the fan mounting

bracket toward the rear of the stove. (Fig. 48) The fan

mounts over two studs that hold the fan just below

the firebox floor. Secure the fan in place with two nuts

provided.

5. Locate the fan speed control/junction box on screw studs

located on the right side of the cover valve. Tighten with

nuts provided.

6. Install thermal sensor element on screw studs located

to the right of the gas valve below the burner base.

7. Reinstall cover valve. Plug in grounded service cord to

a convenient wall receptacle.

This fan assembly is furnished completely

wired. It must be electrically connected and

grounded in accordance with local codes.

US installations:

Follow local codes and the National

Electrical Code ANSI/NFPA No. 70.

Canadian installations:

In the absence of local codes,

follow current CSA C.1 Canadian Electrical Code.

Disconnect the power supply before servicing the fan.

Fan Kits

Black

White

Ground

FP394

WIRING DIAGRAM

11/20/96

Fan

Temperature Sensor

Speed Control

FP105

Fig. 46

FK4 fan wiring.

Refer to Page 28 for rewiring replacement

components.

FP1518

Fig. 47

FK4 fan with existing fan bracket.

FP1519

Fig. 48

FK4 fan kit with replacement fan bracket.

CFMFP

FK24 Fan install

6/04

Stud

Fan Sensor

Location

Fan Speed

Control/Junc-

tion Box

FP150

Fig. 49

FK4 fan installation.

Optional Accessories

Summary of Contents for RFSDV34





































Search results

Summary of Contents for RFSDV34

Reviews:

Related manuals for RFSDV34

Brands by name

Popular brands

Vermont Castings RFSDV34, Installation Instructions And Homeowner'S Manual

Search results

Summary of Contents for RFSDV34

Reviews:

Related manuals for RFSDV34

Brands by name

Popular brands