Vermont Castings RFSDV34 Installation Instructions And Homeowner'S Manual Download

Page: 2 / 36

RFSDV34 Freestanding Direct Vent Gas Stove

10003550

Installation & Operating Instructions

General Information, Warnings, Cautions ...........................................................................3

Requirements for the Commonwealth of Massachusetts ....................................................4

Unit Dimensions ..................................................................................................................5

Locating Your Stove ............................................................................................................6

Clearance to Combustibles .................................................................................................6

High Elevations ...................................................................................................................6

Gas Inlet and Manifold Pressures .......................................................................................6

Gas Specifications ...............................................................................................................6

Preparation ..........................................................................................................................6

Gas Line Installation ............................................................................................................6

Remote Switch Installation ..................................................................................................7

General Venting Information

General Venting Information-Termination Location ............................................................8

General Information on Assembling Vent Pipes ..................................................................9

How to Use the Vent Graph...................................... .........................................................10

Vertical Sidewall Applications & Installation ......................................................................10

Below Grade Installations.. ................................................................................................13

Vertical Through-the-Roof Applications & Installations ......................................................14

Venting Components .........................................................................................................16

Operating Instructions

Glass Information ..............................................................................................................17

Window Frame Assembly Removal ...................................................................................17

Glass Cleaning ..................................................................................................................17

Log Set and Lava Rock Material Installation .....................................................................17

Flame & Temperature Adjustment .....................................................................................19

Flame Characteristics ........................................................................................................19

Lighting & Operating Instructions ......................................................................................0

Troubleshooting NOVA SIT 80 Millivolt Valve ..................................................................1

Instructions for RCSITE .....................................................................................................

Troubleshooting ................................................................................................................5

Maintenance

Cleaning the Standing Pilot Control System .....................................................................7

Wiring Diagrams ................................................................................................................8

Replacement Parts

......................................................................................................................9

Optional Accessories

Fan Kits .............................................................................................................................31

Optional Brass Trim Kit ......................................................................................................3

Remote Control Units ........................................................................................................3

Warranty

.......................................................................................................................................35

Energuide

......................................................................................................................................36

PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THIS APPLIANCE.

Thank you and congratulations on your purchase of an Vermont Castings Group gas stove.

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these

instructions may result in a possible fire hazard and will void the warranty.

Table of Contents

Summary of Contents for RFSDV34





































Search results

Summary of Contents for RFSDV34

Reviews:

Related manuals for RFSDV34

Brands by name

Popular brands

Vermont Castings RFSDV34, Installation Instructions And Homeowner'S Manual

Search results

Summary of Contents for RFSDV34

Reviews:

Related manuals for RFSDV34

Brands by name

Popular brands