![background image](http://html1.mh-extra.com/html/veris-industries/e50h-series/e50h-series_installation-manual_1004650010.webp)
ZL0071-0F
Page 10 of 28
©2018 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 0818
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
TM
E50H2, E50H5 Installation Guide
Quick Setup
Instructions
Use this section to enter:
- BACnet communication parameters
- CT (Current Transducer) output voltage and input current ranges
- The service type to be monitored
These instructions assume the meter is set to factory defaults. If it has been previously configured, check all optional values.
A. To Navigate to the Setup screens:
1. Press
+
+
or
–
repeatedly until
SETUP
screen appears.
2. Press to get to the
PASWD
screen.
3. Press to move through the digits. Use the
+
+
or
–
buttons to enter your password (the default is
00000
).
4. Press to move to the first Setup screen (
S BAC
)
5. Use
+
+
or
–
to select the parameter screen you want to set.
6. After you set the parameters you want, use
+
+
or
–
to select the next Setup screen or to exit the Setup screens (return to
SETUP
).
B. To Enter BACnet communication parameters
1. Navigate to the
S BAC
(set BACnet) Setup screen (see section A above).
2. Press to go to the
MAC
screen and through the address digits. Use
+
+
or
–
to select the BACnet MAC address (default is
001
).
3. Press to accept the value and go to the
KBAUD
screen. Use
+
+
or
–
to select the baud rate (default is
76.8K
).
4. Press to go to the
ID1
screen and through the upper four digits of the Device Instance. Use
+
+
or
–
to select the ID digits.
The setup screen splits the Device ID into two parts, the most significant four digits (ID1) and the least significant three digits
(ID2). The E50Hx supports BACnet Device ID values from 1 to 4,193,999. Units are shipped with a factory default setting that is
pseudo-randomly generated in the range from 1,000,000 to 3,097,151.
5. Press to accept the value and go to the
ID2
screen and through the lower three digits of the Device Instance. Use
+
+
or
–
to
select the ID digits.
6. Press to accept the value and go back to the
S BAC
screen.
C. To Enter the CT (Current Transducer) output voltage and input current ranges:
1. Navigate to the
S CT
(Set Current Transducer) Setup screen (see section A above).
2. Press to go to the
CT V
screen. Use
+
+
or
–
to select the voltage mode Current Transducer output voltage (default is
1.00
).
3. Press to go to the
CT SZ
screen and through the digits. Use
+
+
or
–
to select the CT size in amps (default is
100
). accept the
value and
4. Press to accept the value and go back to the
S CT
screen.
D. To Enter the service type to be monitored:
1. Navigate to the
S SYS
(Set System) Setup screen (see section A above).
2. Press to go to the
SYSTM
screen. Use
+
+
or
–
to select the configuration (see wiring diagrams - default is
3LN
-
1N
).
3. Press to go back to the
S SYS
screen.
For full setup instructions, see the configuration instructions on the following pages.