Verilink WANsuite 5165 Reference Manual Download Page 68

3-38

W A N s u i t e   5 1 6 5

The PPP Statistics screen provides the following user-activated buttons: 

PAP Table

At the bottom of the PPP Services Details screen are buttons that display 
tables for PAP and CHAP details. The PAP Table (Figure 3.33) displays the 
Usernames and Passwords for 10 entries. 

Figure 3.33

PAP Table Screen 

Select an Index number and click the “PAP Details” button at the bottom of 
this screen to bring up a PAP Details screen (Figure 3.34) in which you can 
view, change, or delete the Username and Password for that particular PAP 
Index. 

Figure 3.34

PAP Details Screen 

To change the Username and Password for a selected PAP Index (PAP: 1 in 
the example above), enter the new information in the appropriate fields and 
click the “Submit” button. 

Button

Function

Submit

Sets any values that have been changed.

All PPP Intervals

Opens the PPP Statistics screen that shows all statistics for all 
parameters.

Type Details

Returns you to the PPP Service Details screen.

Clear Stats

Clears all PPP statistics.

Summary of Contents for WANsuite 5165












































































































































































































































Reviews: