manualshive.com logo in svg

Verilink WANsuite 5165, Reference Manual

Share
Download
Verilink WANsuite 5165 Reference Manual Download Page 192

4-68

W A N s u i t e   5 1 6 5

Figure 4.60

Area Table Screen

The fields displayed on the Area Table screen are described below. 

Area Details Screen

This screen (Figure 4.61) displays the details associated with a defined Area.

Figure 4.61

Area Details Screen

Field

Description

Area ID

Displays the ID of the Area (represented by an IP address).

Ena

Displays whether the defined area is enabled or disabled.

Auth Type

Indicates Area validation.

Stub

Displays whether or not the defined area is a Stub Area.

Addr Summary

Displays the Address Summary of the defined Area.

Mask Summary

Displays the Mask Summary of the defined Area.

Ad

Displays whether advertising is enabled or disabled for this Area.

Summary of Contents for WANsuite 5165












































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands