Vemco VR4-UWM User Manual Download Page 8 | Manualshive

Page: 8 / 75

Vemco VR4-UWM User Manual Download Page 8

VEMCO – VR4-UWM Manual

2

VR4-UWM features include:



Acoustic modem with omni-directional transducer and fast wakeup eases station-keeping and supports
speeds up to 1200 bps



Detects all current VEMCO 69 kHz and 180 kHz coded tags



Bluetooth® wireless technology for high speed in-air communication



A two-color status light indicates system status and ping detection on each acoustic data channel



16 megabytes of flash memory stores (approximately 800000 detections) as well as diagnostic raw data
logs



Two battery options: lithium for extended life, or alkaline for easier and less expensive shipping to
international locations.



Automatic battery management displays the remaining capacity of the battery, making it easier to
schedule replacement.



A Suspend mode to conserve the battery during shipping or extended storage. No need to disassemble the
unit to disconnect the battery.



Tilt, temperature, and battery voltage sensors monitor the operating condition of the receiver



Optional password protection to prevent unauthorized access using the acoustic modem



Supported by VEMCO VUE software (version 2.0 and greater)

The VR4-UWM records the tag code ID number, the date/time of valid detections, and sensor data if the
acoustic tag received is equipped with a sensor. This information is stored in the receiver’s memory until
offloaded from the receiver to a PC running VUE software using either the acoustic modem or Bluetooth
wireless communication.

VR4-UWM Quick Facts

Dimensions

Height: 50.3 cm (19.81”)
Max Diameter: 22.2 cm (8.75”)

Weight

With lithium battery, no external connector

In sea water: 2.1 kg (4.6 lbs) sinking

With alkaline battery, no external connector

In sea water: 2.99 kg (6.6 lbs) sinking

Receive
Frequency

69.0 kHz and 180.0 kHz

Operating
temperature

-5°C to +40 °C (Water must not freeze)

Maximum
Depth

500 meters (730 psi)

WARNING

The VR4-UWM pressure case and
seal have a maximum static depth
rating of

500 meters

(730 psi).

Physical shocks to the receiver, such as
bumping into a solid object, when it is at any
depth can result in a considerably higher
pressure on the casing than just the depth
pressure and water may enter the VR4-UWM
case. If the O-rings or their mating surfaces
are dirty or damaged, then water may also
enter the receiver case. If you are suspicious
that water has entered the receiver, then follow
the suggestions in section 8.2.2 for
troubleshooting a pressurized case.

«
...
6
7
8
9
10
...
»

Summary of Contents for VR4-UWM












































































Reviews:

No comments