Vemco VR4-UWM User Manual Download Page 59 | Manualshive

Page: 59 / 75

Vemco VR4-UWM User Manual Download Page 59

VEMCO – VR4-UWM Manual

53

6.8

Battery

The VR4-UWM receiver is powered by a custom battery pack with an integrated fuse and EEPROM device
for tracking the remaining capacity.

The VR4-UWM is usually shipped with the battery installed and

connected, so there is no need for the customer to disassemble the receiver to connect the battery. To avoid
consuming the battery during shipping and storage, VR4-UWM can be placed in Suspend mode (see section
5.5.1 for details).

The battery pack is NOT rechargeable. Properly dispose of the battery pack in the
appropriate manner when it is depleted.

There are two battery types offered for the VR4-UMW, lithium batteries and alkaline batteries. Lithium
batteries have a much longer life (see table below) but transportation is restricted under dangerous good
regulations, which can be a problem in some areas. These restrictions are explained in section 9.2.1. Alkaline
battery packs do not have transportation restrictions.

Estimated battery life

Estimated Life with…

Tadiran Lithium Battery

Alkaline Battery

both channels on

71 months

19 months

only 69kHz channel on

117 months

31 months

only 180kHz channel on

84 months

22 months

Battery life estimates are based on typical usage of downloading 100 Kbytes of data per month over the acoustic
modem. More frequent offloads and larger data records will decrease the life expectancy of the battery.

Lithium metal D-cell batteries are classified as

Dangerous Goods

and must be

handled according to UN Recommendations on the Transport of Dangerous
Goods (UN3090 for batteries alone; UN3091 for batteries contained in
equipment or packed with it). See the MSDS for more information.

VR4-UWM battery pack, available in Lithium or Alkaline

Battery packs look
identical. The labels
identify if the battery is
Lithium or Alkaline.

The battery pack is

NOT rechargeable

.

«
...
57
58
59
60
61
...
»

Summary of Contents for VR4-UWM












































































Reviews:

No comments