manualshive.com logo in svg

Velbus VMB4RYLD, Installation Manual

Share
Download
Velbus VMB4RYLD Installation Manual Download Page 69

VELBUS INSTALLATION GUIDE 

©2015 Velbus 

69 

www.velbus.eu 

To begin with, most modules have a large range of built-in actions, including: 
inhibiting  and  forcing  actions  with  two  levels  of  priority,  multiple  types  of 
timers  and  time-dependent  programming  of  channels.  Free  (real  or  virtual) 
channels  of  relay  modules  can  also  be  used  as  virtual  switches,  allowing 
conditional actions to be configured, and many different actions and programs 
can be used together in the same module. 

Interval timers are also available, for example, an eight hour timer where the 
contact closes for 10 minutes, then opens again and waits for an hour. Actions 
can  be  triggered  by  closing  or  opening  of  channels,  by  pressing  or  releasing 
buttons, by temperature or time alarms, and so on, while virtual relay channels 
allow all kinds of AND-, OR-, IF-THEN and other logical configurations. 

For  those  who  need  even  more  advanced  programming,  the  VMBHIS  Home 
Center  server  comes  with  a  built-in  logical  module,  allowing  all  inputs  and 
outputs and various special elements (Sonos® triggers, IR command codes, et 
cetera) to be connected through a high-level programming interface.  

What happens to the time and date setting after a system power loss? 

The actions and settings that have been programmed in the modules will never 
be  affected  by  a  power  loss.  As  far  as  time  and  date  restoration  goes,  the 
following options exist. 

1. With the VMBHIS Home Center server 

The VMBHIS Home Center server synchronizes time and date regularly with an 
online  time  server.  Shortly  after  a  power  loss,  time  and  date  will  be 
automatically restored. 

2. With a VMBLCDWB module 

A VMBLCDWB push button and timer module can automatically restore time 
and date. This module accepts a backup battery to maintain the time and date 
during a power outage. 
 

The  VMBLCDWB  needs to  be  set  as  “master  clock”.  This  can  be  done  from 

within Velbuslink -> Configuration settings -

> tab “Preferences”. When power 

is restored after a power failure, all other modules will copy the time and date 
from the master clock. 

Summary of Contents for VMB4RYLD







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands