background image

Introduction

Contractor Certification Requirements

4

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 

equipment discussed in this manual:

Service Technician Certification (Previously known as Level 2/3):

 Contractors holding valid Technician 

Certifications are approved to perform installation checkout, startup, programming and operations training, system 

tests, troubleshooting and servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak 

Detection.

TLS-4xx Technician Certification:

 Contractors holding valid TLS-450 Technician Certifications are approved to 

perform installation checkout, startup, programming and operations training, troubleshooting and servicing for all 

Veeder-Root TLS-450 Series Tank Monitoring Systems, including Line Leak Detection and associated accessories.
All service personal on site must comply with all recommended safety practices identified by OSHA and your 

employer.
Review and comply with all the safety warnings in the manuals listed in this document above and any other 

Federal, State or Local requirements.

Warranty Registrations

 may only be submitted by selected Distributors.

Related Manuals

577014-466

HydrX™ Fuel Conditioning Controller Setup & Operation Manual

577014-469

HydrX™ Fuel Conditioner Mag Probe Replacement Instructions

577014-470

HydrX™ Fuel Conditioner Pressure Sensor Replacement Instructions

577014-472

HydrX™ Fuel Conditioning System Quick Help

577014-473

HydrX™ FC Inlet/Outlet Filters Replacement Instructions

577014-474

HydrX™ FC Waste Water Tank Draining Instructions

577014-073

TLS-450PLUS Site Prep and Installation Manual

577014-072

TLS-450PLUS Operators Quick Help Guide

577014-110

TLS-450PLUS/TLS4 Operator's Manual

576013-858

Direct Burial Cable Installation Manual 

HydrX System Parts

Table 1.  

 

HydrX System Parts List

Part Number

Description

Qty. Req’d.

860400-001

Fuel Conditioning Controller- w/ 6’ cable

1 per site

8605X0-050

Fuel Conditioner - 5 gal. water holding capacity

1 per tank

8606XX-XXX

Water Intake Device (WID) 

1 per tank

8607X0-XXX

Guide Tube 

1 per tank

330020-867

Kit - RISER - 15.5"

1 per tank

330020-874

Kit - Installation - Fuel Conditioner for FE Petro

®

 pump

1 per tank pump 

type

330020-875

Kit - Installation - Fuel Conditioner for TRJ pump

Summary of Contents for HydrX








































Reviews: