17
6
22 mm
5
1
2
4
3
7
10
Gerad front
och gavel
Front framför
gavel
11
11
9
ca 75 mm
13
8
14
12
Mitred front and
decorative side.
Front in front of
decorative side.
6
22 mm
5
1
2
4
3
7
10
Gerad front
och gavel
Front framför
gavel
11
11
9
ca 75 mm
13
8
14
12
Mitred front and
decorative side.
Front in front of
decorative side.
position (e.g. when the dishwasher door has plywood panels behind). In
that case, use plinth art. no. 3868 or 3868K with dimensions 600x115x16
mm, which is fitted to adjoining plinths with jointing plate art. no. 39332
measuring 116x18x2 using screw TKX 4.0x12 mm. For some slightly taller,
fully integrated dishwashers, the supplied partition strip art. no. 47148 for
width 600 mm or 47149 for width 450 mm, which is installed above the
dishwasher, must be cut to adjust its height, which is performed on site.
11. Strip for protruded plinth art. no. 3869 or 3869K, with dimensions
596x38x21 mm, is installed on the bottom edge of the dishwasher door
with accessory bag art. no. 39221. The pre-drilled strip is placed against
the underside of the dishwasher door and the location of the holes in
the door is marked. Remove the strip and drill in the door using a 2 mm
drill. Place the spacers between the door and the strip and screw in
with the supplied screw TFXH 3.5x50 mm. Then install the door on the
dishwasher. Check that the door can be lowered without catching on
the plinth, and also check that the lower strip on the door is free from
the dishwasher’s plinth in the lowered position. If it is not free, it must
be cut at the bottom edge.
12. When there is a decorative side installed outside the dishwasher
that goes down to the floor, a supporting leg attachment is mounted
horizontally on the decorative side down by the floor, although above
the dishwasher’s drain tray, and a supporting leg is installed in the
supporting leg attachment. The mounting attachment is turned 90° on
the plinth to achieve a stable attachment in the corner, which would
otherwise be free with no support. The supporting leg attachment must
be removed if the dishwasher is to be pulled out.
13. Place the plinth in position by placing the plinth clip against the
supporting leg and then clamping the clip around the supporting leg.
14. In the case of sides going down to the floor on e.g. a kitchen island (for
the sake of stability), the front piece and the end piece (outside the end
of the decorative side) are mitred. The end piece can then, if necessary,
be screwed into place from inside the decorative side and out into the
plinth using connection screw art. no. 39611 TFX 4.0x28 mm.
In this case, the mitring must not be glued, as this would make it
impossible to remove the plinth. Alternatively, the connection screw
is positioned from the outside as far back and as far down as possible.
After this, the screw head can be covered with a white cover plug, 20
mm, with art. no. 39226, which must be ordered additionally. In the case
of a coloured plinth, the cover plug must first be painted with touch-up
paint before it is fitted. Roughen the surface of the cover plug using
fine sandpaper and paint one to three times, until it is properly covered.
Another option instead of mitring is to position the plinths so that they
meet each other in the corner.
1. Installing base and tall cabinets
1.11 CONT. INSTALLING THE PROTRUDED PLINTH
6
22 mm
5
1
2
4
3
7
10
Gerad front
och gavel
Gerad front
och gavel
Front framför
gavel
Front framför
gavel
11
11
9
ca 75 mm
13
8
14
12
6
22 mm
5
1
2
4
3
7
10
Gerad front
och gavel
Gerad front
och gavel
Front framför
gavel
Front framför
gavel
11
11
9
ca 75 mm
13
8
14
12
NOTE! Shows the back of the plinth