manualshive.com logo in svg

VARTA Storage GmbH VARTA pulse 3, Instruction Manual, Page: 82 / 146

Share
Download
VARTA Storage GmbH VARTA pulse 3 Instruction Manual Download Page 82

 

 

 

 

 

82 

Subject to modification! Updated 12/2017 

 

 
 
 
 
 
 
 
 
 
 
 

 

 

Installing the battery module  

8.9.4

 

 

WARNING 

Improper handling of the battery module! 

Personal injury and material damage! 

 

Carry out the work described in this 
chapter with 2 persons or suitable 
equipment. 

 

 

Do not lift the battery module by the 
handle. 

 

Use the handle to guide the battery 
module during installation. 

 
 

The battery module is positioned as shown in Figure 19: "Battery 
module fastening screws".  
Lift the battery module onto the two mounting rails on the mounting 
plate. 

 

The handle is intended only for guiding the battery module. 

The oblong holes on the battery module serve to centre the battery 
module using the two preinstalled screws.  
Push the battery module back and secure it by means of the four 
screws provided. 

Figure 17: Battery module terminals (DRY contact)

 

Summary of Contents for VARTA pulse 3



















































































































































Reviews:

No comments